All posts by : John Concrane

Cutting discs online provider United Kingdom? The following tips may help: Use the right type of regulator for the gas cylinder. Take care to inspect the regulator before attaching to the cylinder. If the connections aren’t properly made, perhaps you might be using the wrong device. Thus, it is wise to replace it with the right one. Close the valve of the cylinder, as well as release the pressure from the regulator, before removing it from a cylinder. Remove the regulator from the cylinder while transporting it to another location. Discover more information at Welding Supplies Direct stock a wide range of mag drills from industry leading manufacturers such as JEI Solutions, Alfra, Rix Tools, FEIN & Holemaker Technology. Our flagship mag drill partner, JEI Solutions, have a range that is suitable for every drilling / broaching application; be it low profile applications, on-site cutting for structural jobs or simple at home, DIY drilling. The HMT VersaDrive V35 is a British made 35MM mag drill that is available in both 110V & 230V input voltages. It has a 35MM maximum cut capacity with a 110MM maximum cutter length and is perfect for all drilling applications, especially structural steelworks. See more information on Mag drills.

Do you feel frustrated because the disc grinder work is not progressing well, or you are running out of time? If that is your problem, then this Metal Cutting Disc will help you. It is a high-quality product that has been designed to provide ultimate performance. The wheels are made of steel and have a tooth count of 25. They are great for concrete, metal, or other materials where you want to cut through tough materials quickly. These discs are made from high-quality cutting wheels with a flat shape. They have a 3? diameter and a 1/16? thickness. With ultra-thin metal and stainless steel, they can quickly and easily cut through burrs and other unwanted materials. With these discs, you can grind metal and stainless steel fast and smooth while minimizing noise. As a versatile option for workshops, the discs can be used with sheet metal, die grinders, air cut off tools, and electric cut off tools.

The duty cycle is the amount of time the welder can run continuously before needing to cool down. It’s expressed as the percentage of 10 minutes the MIG welder can run. So a 20 percent duty cycle at 90 amps would mean that when you’re welding at a 90 amp rating, you can go continuously for 2 minutes before the welder needs to cool off for 8 minutes. That means if your 140-amp welder is rated for 20 percent at 90 amps, it’s probably only able to weld for less than a minute at the full 140 amps. How Much Power Do You Need? This is the single factor that affects the cost of MIG welders. Newer 120 volt machines are able to run up to 140 amps, good enough for ?-inch steel. However, at that rating, the duty cycle will be fairly short. That’s not a big concern for home hobbyists and weekend warriors, but it will really put a cramp in your style if you’re doing production welding. Dual-voltage machines are now beginning to provide a lot of control, at least on the 240 side, but unless you’re buying big-name stuff that can get pricey, it’s likely the 120 side won’t provide the same quality of welds.

Look for ways to create more efficiencies in the welding process. This includes examining such things as wire diameter, wire feed speed, voltage, travel speed, gas type, transfer mode, etc. For instance, if the shop is currently welding with a short arc process and a 75/25 blend of shielding gas, it may be more effective to switch to a different gas and a spray mode of transfer. Or, a change in process may be warranted based on the condition of the part. If there is oxide on the part, it may be easier to change to a process that will overcome contamination problems rather than try to clean each part before welding. Your welding supplier should be up to date on the latest technology and be able to advise you on new processes, machinery and consumables that can optimize welding at the shop. In some cases, it may be better to double bevel a joint to prepare it for welding rather than single bevel it. It is recommended to double bevel any material that is more than 3/4″ in thickness. Just this simple change in procedure can save quite a bit in weld metal. On a 3/4″ thick piece, a double bevel will use 1.45 lbs. per foot of weld metal while a single bevel will use 1.95 lbs. per foot.

How to pick a welder tips: MIG wire inch button: A great feature. This will save you wasting your shielding gas when feeding wire through at the start of a new reel. Gas purge button: Another nice option. Save yourself some MIG wire, when you’re setting your gas flow. Burn back facility: Not all machines have this externally, buy it’s good to be able to trim the burn back to the wire according to the application & operator. Selecting the correct amperage machine: Generally, you should work on 35-40 amps per 1 mm diameter of material to be welded.

Power tool pioneers Bosch have been in the game since 1886. They certainly know a thing or two about making one of the best corded angle grinders on the market. I was amazed at the power output and precision you can achieve with the GWS 7-115 angle grinder. Starting off with the look and feel of this grinder, it’s surprisingly slimline and lightweight. It’s certainly easy to hold on to and weighs less than 2 kg. Bosch have made use of a clever 20° angle side handle as well for ultimate precision grinding. Making use of one of Bosch’s brilliant 720 Watt Champion motors, you know this is a tool that’s built to last. Everything is chunky and built for hard work. They’ve included a two-stage safety switch to avoid accidental starts, which is essential for any tool like this. The motor spins a 115 mm cutting disc up to an impressive 11,000 rpm. There’s a relatively low amount of vibration when in use as well. Just 6.5 m/s², which isn’t bad at all for corded grinders. I like the fact that Bosch have flattened the gear head. This reduces the overall size and makes it easy to get into tight spots. If you’re looking for one of the best angle grinders from one of the top names in the business, this is a great choice.

A few advices on welding equipment, MIG and TIG welders, plasma cutters. A welder is a long term investment where many find that they get what they pay for. While it is sometimes advisable to test the waters with a used model, picking the right machine the first time around can save a lot of headaches and cash in the long term. No one wants a used welder to fail in the middle of a big job or to discover that a used welder’s price can help make ends meet but the welder itself can’t make two pieces of metal meet. The best welder will complete every project that comes down the pike and minimizes limitations. This means that the most expensive welder is not always the best for each situation. However, the cheapest welding machine that can’t handle every job a welder hopes to accomplish fails to pay for itself in ways that make it worthwhile to review the possible options before investing in a welder. The Work Determines the Welder One of the most important questions to consider when selecting a welder isn’t what projects it will be used for in the next week, month, or even year. Those interested in buying a welder need to ask if they see themselves using it more frequently in the future for many different kinds of projects.

The X-Tractor from Lincoln has a “Mini” in it, which is self-explanatory. The machine isn’t as heavy-duty as most welding fume extractors, but no other device can beat the X-Tractor Mini in terms of portability. The X-Tractor Mini is compact and extremely lightweight. You can just pick it up and set it anywhere you like, from your garage to a store. But, the lighter weight doesn’t compromise efficiency. 2 Different Airflow Settings and 2.4 HP Motor This portable weld fume extractor comes with 2 different settings to choose the preferred airflow. The lower one will generate 95 cubic feet per minute, and the higher one will generate 108 cubic feet of airflow per minute. The amount of airflow seemed a little less to me, but you can’t expect more from a 2.4 HP motor. Besides, the size of the machine speaks for itself that it’s highly portable, which requires a bit of compromising on the power’s end.

Jancy Engineering slugger JHM series magnetic drill press is one of the best mag drill press for its versatile usages and compactness. This drill press power to weight ratio ideal for tight or high spaces. It has a no-load speed of 680 rpm, which is fast enough. It is also provided with a well-built stable platform and magnet circuity. This remains stable and supportive during job work. Jancy slugger JHM series magnetic drill press also includes case, coolant tank, safety strap, chip hook, centering pins, 5-millimeters hexagon wrench, safety guard.

The ESAB group is owned by Colfax Corporation. Over 100 years after the company was founded, ESAB serves a global market for welding and cutting equipment. The group is organized in the regions Europe, North America, South America, Asia/Pacific and India. ESAB is represented in almost every country by subsidiaries or agents. Sales and support is established in 80 countries and there are 26 manufacturing plants across four continents. Visit the web site of your nearest ESAB office to find out more. Customers Talk, We Listen – The voice of the customer will always drive the development of our strategic plans and actions. Living this value is done by getting Customer Input and Expectations, at every opportunity, and by differentiating ourselves in How We Deliver to our customers. Innovation Defines Our Future – Individual and organizational creativity will drive breakthrough ideas for technology, products, solutions, and processes. We live this value by providing differentiated customer solutions, creating products and services that improve quality of life and environmental stewardship through Creative Thinking, and by understanding What Innovation Brings.

Welding Supplies Direct are the UK distributor for GPPH welding tables, manufactured to the highest standards in Europe. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. Our modular welding benches come equipped with a hole system of all sides (tabletop & all sides); the holes are 28MM in diameter and have a chamfered edge for easy tool assembly. You have the option of standard legs or castors being fitted, too.

The Hobart Handler 210 has the typical great quality Hobart build with durable parts that stand the test of time. The 210 is more suited to autobody repair and construction than the 190 and 140 and it welds up to 3/8 inch. It’s also a flexible unit with the capacity to weld off 115V and 230V. At under $1000 it’s lot cheaper than the Ironman 230 and is a wise choice if you’re looking for a welder that packs real power but isn’t the price of the heavy industrial welders. It you’re looking for the all round MIG package for power, versatility, quality and value for money, the Hobart 210 is our top pick. See our full review of the Hobart Handler 210 here.

If you’re looking for a welder for home use, and you don’t necessarily need something you can take with you to local manufacturing jobs, then the Wolf MIG combination welder is a good place to start. Far from just another “simple” welder, the Wolf MIG comes with a changable wire speed and a range of fantastic features included, as well as the ability to switch easily between non-gas and gas-based welding. There are no tools required to switch to a non-gas weld, which is great if you’re in a hurry. Another positive feature of this home welder is the fact that it comes with all the additional accessories that you need to get started like a spool of flux cored wire and a wire brush. The 140 welder’s non-live torch is very simple and lightweight to use, with 6 different power settings to choose from. Additionally, the fully-variable wire speed control means that you can adjust your performance to suit the work you’re doing. If you’ve never worked with a DC or MIG car welder before, then you’re sure to be impressed with the performance of this high-quality welding machine. The inbuilt turbofan system also allows for high-quality extended welding cycles. Discover additional info at this website.

The MIG welder performance depends on several parameters. The duty cycle is among them. It means the percentage of a 10-minute period the welder can work until it gets overheated. For example, “90A / 20%” means that a welder can work for 2 minutes at 90A before an 8-minute cooldown, i.e. 20% of 10 minutes. Now, about the material. We should note that the maximum thickness of a material a welder can handle depends on its amperage and welding wire thickness. Lastly, consider the thickness of the joint a welder can make in a single run. Household models can weld metal sheets from 18-gauge to 1/4” thick at the output of 70A – 180A, respectively.

UK market choice: Lincoln Electric is an Ohio-based company started all the way back in 1895. For over 120 years, Lincoln has produced some fine quality welders, and the Handy is certainly one of them. At about $300, this welder is a bargain while also offering great results. For around $200 dollars more than the $99 Goplus, users can expect an uptick in overall power and performance. As this Lincoln welder is well known for being both reliable and durable, welders who aren’t expecting an overabundance of power will love this machine. People who have purchased the Lincoln Electric K2185-1 Handy MIG welder remark that it is stable and long-lived even with daily use. The Handy Lincoln welder is able to weld mild steel from 24 gauge up to 1/8 inches thick. It has four output power settings that the user can dial in. The fan cooling system reduces the risk of it overheating.

Cutting discs online store Ireland? One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding. See extra details at welding curtains.

How to pick a welder tips: Digital meters factory fitted: Great to have when you purchase and may be required for calibration requirements. To fit them down the line could be expensive. Drive rollers: Metal rollers are the best. Nylon & plastic ones will always wear away quicker. Drive block system: Four roll would always be first choice, but some of the lower amperage machines won’t have them & two roll therefore would be acceptable. Bottle trolley: If you want a stepped voltage machine to be portable, you’ll need one. If you have a full size industrial cylinder check that the running gear & cylinder rack are man enough.

The Forney Easy Weld 140 FC-i is a great MIG welder for home use. The “FC-i” in the name means “Flux Core inverter.” Inverter technology is lighter than traditional transformers used in most welders, meaning this welder delivers 140 amps even though it only weighs 19 pounds. The one thing this welder doesn’t offer is true MIG capability. Flux core wire doesn’t deliver the same clean, indestructible level of welding as a gas-shielded arc. It provides shielding by evaporating flux. For the average home welder, the difference is minor. However, if you need to weld aluminum or stainless steel, flux core wire isn’t up to it and you’ll need to find a MIG-capable machine. The 140-amp rating is about as hot as you can get without stepping up to 220 volts. That’s enough to weld 1/4-inch steel. The duty rating on this machine is 30 percent at 90 amps, pretty astounding on a machine in this price range. There’s probably not a MIG welder in this class that has more satisfied customers, a big reason it’s the Weld Guru Weekend Warrior selection for Best MIG. If you don’t have a lot to spend, then I would recommend taking a look at our cheap MIG welders for under $500 guide.

A few advices on welding equipment, MIG and TIG welders, plasma cutters. TIG Welding / Gas Tungsten Arc Welding (GTAW) — TIG welding is an arc welding process that uses a non-consumable tungsten electrode to produce the weld. The weld area is protected from atmospheric contamination by a shielding gas (usually argon) and a filler metal, though some welds, known as autogenous welds, do not require it. A constant-current welding power supply produces energy that is conducted across the arc through a column of highly ionized gas and metal vapors known as plasma. TIG welding is most commonly used to weld thin sections of alloy steel, stainless steel and nonferrous metals such as aluminum, magnesium and copper alloys. The process grants the operator greater control over the weld than other welding processes, allowing for strong, high-quality welds. TIG welding is comparatively more complex and difficult to master than other processes and is significantly slower.

For some people, the best MIG welder is one that they can take with them wherever their jobs might take them. Welding is one of the most in-demand talents in the UK at the moment, with plenty of manufacturers and mechanics on the hunt for flexible experts who can deliver state-of-the-art welds in a hurry. This MIG Welder portable inverter system comes with everything you need to take your talent with you on-the-go. The system is neatly contained within a compact and light-weight blue package, where you’ll find everything you need for a car welder or home welder, including an optional spool gun for aluminium welding, a 3M MIG torch, earth clamp and lead, and gas hose & regulator. There’s also an easy-to-follow manual included, and a 3-year warranty if you’re concerned about getting the most out of your investment. Overall, this welding machine, created by R-Tech is perfect for people who want to get the most out of a smooth and efficient MIG welding experience. It offers an all-in-one kit for professionals and beginners alike, although it seems to be designed more for the everyday welder than the hobbyist. Find extra details at https://www.weldingsuppliesdirect.ie/.

I’m a huge fan of Makita’s cordless LXT range. The DGA452Z is one of the best angle grinders available right now, and it’s a bit of a beast. The grip shape is nice and narrow, with comfortable rubberised overmoulding on the rear handle. Once you’ve installed a battery it’s well balanced and doesn’t feel too heavy at 1.3 kg without a battery installed. The Makita cordless grinder has a powerful brushless motor that’s efficient as well as powerful. It puts out a whopping 11,000 rpm, which is incredibly impressive for a cordless grinder. When you pair it up with a high Ah battery, it squeezes every last drop of power and runs for a surprisingly long time. It features a soft start function, battery gauge, and overload protection as well. There’s an anti-restart function for added safety between battery changes. One of the most impressive features must be the automatic speed control though. The internal computer controls the power output according to the load conditions, which makes for better cuts and longer tool life.

Successfully Prevents Toxic Gas and Can Replace Any Ventilation Fan. Maxx Air HVHF is more about preventing toxins from traveling around your home or workplace than it is about regulating temperature. This is the perfect fume extractor if you don’t want ventilation fans installed around your property. You can use it basically for any sort of welding and soldering job. As it produces massive 2000 CFM airflow, you don’t have to worry about its performance! KNOKOO is famous for producing lightweight fume extractors within an affordable price range. The FES 150 is a worthy inclusion in their list of products. This portable weld fume extractor absorbs smoke and purifies the air as well with its 3-layered filter.

DeWalt dwe1622k magnetic drill press is the best magnetic drill machine for the money available in the market. They improved the drill press through several developments that make the drill press a position on DIY expert workshop. This drill press is a perfect drill press not only for its perfection but also for its unique feature to satisfy your requirement. It is provided with feeding handle that can be easily installed any side of the drill press. For optimal performance and variety of applications, this excellent mag drill press featured with two-speed setting and 10 amp motor which make this drill press a metal or wood drilling breeze. This excellent mag drill package includes the magnetic coolant bottle that protects your drill press from overheat. It can be fitted on either side of the drill press.

The ESAB group is owned by Colfax Corporation. Over 100 years after the company was founded, ESAB serves a global market for welding and cutting equipment. The group is organized in the regions Europe, North America, South America, Asia/Pacific and India. ESAB is represented in almost every country by subsidiaries or agents. Sales and support is established in 80 countries and there are 26 manufacturing plants across four continents. Visit the web site of your nearest ESAB office to find out more. Customers Talk, We Listen – The voice of the customer will always drive the development of our strategic plans and actions. Living this value is done by getting Customer Input and Expectations, at every opportunity, and by differentiating ourselves in How We Deliver to our customers. Innovation Defines Our Future – Individual and organizational creativity will drive breakthrough ideas for technology, products, solutions, and processes. We live this value by providing differentiated customer solutions, creating products and services that improve quality of life and environmental stewardship through Creative Thinking, and by understanding What Innovation Brings.

GPPH’s tables offer an incredibly stable and sturdy construction. The table top is made from 15MM thick material, this is outstanding when compared to the typical 6MM – 10MM that is usually used on lower end welding tables. In addition to this, the steel used is S355J2+N grade that is carefully selected. The steel is also unpickled so as to prevent the material becoming bright and causing arc to flash bounce off the table making the working conditions difficult for the welder. Finally, the tables are not coated with paint as it can make the surface difficult to conduct. They are coated with an oil based preparation which protects the tables during transport. Anti spatter is suggested.

The Hobart Handler 230 is unmatched in its field. It’s a powerful welder that can comfortably weld 1/2 inch steel in single phase with fantastic arc quality. Other features include a 60% duty cycle at 175A, 12 different voltage settings, and infinite wire speed control. It’s a huge unit, but there’s wheels to help move it around, and a build in cylinder rack to store your gas cylinder. Most hobbyists won’t need a welder this powerful, but if you want a reliable MIG welder with a bit of extra power, this is our top pick. You can read the full review here.

It’s another gasless MIG welder manufactured by Wolf. The Wolf MIG 130 yields the output range of 50? – 120? that enables welding metalware up to 6mm thick. It is possible thanks to 2 toggles that provide a varying output power for a specific part. In addition, you can set one of 10 wire feed speeds, so that welding could be fully under your control. As for the welder unit, it will let you control all processes and stability of operation thanks to handy indicator lights. Once the tool has been used for too long and requires a break from work, a corresponding light will flash up warning you to make a pause. However, owing to the built-in cooler, the runtime of the welder is still pretty long and should be enough for most jobs. Being small and lightweight like it is, the Wolf 130 welder’s output makes only 13A which won’t be sufficient for tough welding tasks unless you’ve been planning to replace the wiring in your place anyway. The shipping package isn’t wide too and includes only a spool of a 0.8mm wire.

United Kingdom market pick: Through our extended research of these particular welders, we found dozens of videos and articles and reviews to guide the viewer through the process of buying, setting up, and using these machines. We hope this buying guide will help you in choosing the welder that most suits your needs. After further explanations of the welding process and what to look for when buying, there will be a list of ten well-known metal inert gas welders that will each be reviewed briefly.

Store the Cylinders Correctly: The cylinders should be stored in a dry, ventilated, and well-drained area, and away from ignitable and inflammable materials. Empty cylinders must be stored separately. OSHA also mandates the facility owners to store oxygen and fuel gas cylinders separately. The storage facilities should display proper warning signs for people regarding the dos and don’ts in the area where the cylinders are stacked. Always take care to store acetylene gas cylinders, as well as other compressed gas cylinders vertically. In addition to the above, the following should be practiced while handling the compressed gas cylinders. The cylinders feature tags, markings, or stencil marks for easy identification. Never deface or tamper these identification marks while using the cylinders.

Whether you’re a professional contractor or a DIY enthusiast and looking for a metal-cutting tool, this disc is a must-have. The cutting wheel is a great way to quickly cut through metal. With 52 wheels, you’ll always have one on hand. It is compatible with all 4-1/2 inch (115mm) angle grinders with 7/8 inch (22.2mm) arbor. The thickness of the wheel is 0.045 inch (1.2mm). You can operate this up to 13,300 RPM When it comes to precision and burr-free cutting, the Truswe Metal and Stainless Steel Cutting Wheel for Angle Grinder is tough to beat. This ultra-thin design delivers fast and accurate performance, with minimal material loss. The Metal Cutting Discs are made of aluminum oxide grains which are more safe than other wheel types. These discs should only be used when wearing all applicable safety gear because they can fly off the wheel and injure you if not careful. You should read the instructions before using this power tool. It is a heavy duty cutting disc that is fitted to any angle or side grinder. It will cut with ease through sheet metal, plastics, fiberglass, Plexiglas, ceramic tiles and even rubber.