Spring seals manufacturer from dmsseals.com: At the heart of why a mechanical seal works lies the rotating and stationary seal faces. Seal faces are lapped so flat it is impossible for a liquid or gas to flow through them. This allows for a shaft to spin, while a seal is being maintained mechanically. What determines the amount of time a seal will last is selecting the right seal material combination for the application. Hard seal faces for abrasive service, Carbon Vs. Ceramic for simple water (or anti-freeze in the case of automotive applications). Carbon Vs. Silicon Carbide for most applications to reduce energy consumption and provide long life. For critical applications double mechanical seals are usually recommended. Read additional details at https://www.dmsseals.com/.
The Primary Seal – While two of the sealing points in a seal design are simple static seals, the seal between the rotating and stationary members needs a little more consideration. This primary seal is the basis of all seal design and is essential to its effectiveness. The primary seal is essentially a spring loaded vertical bearing – consisting of two extremely flat faces, one fixed, one rotating, running against each other. The seal faces are pushed together using a combination of hydraulic force from the sealed fluid and spring force from the seal design. In this way a seal is formed to prevent process leaking between the rotating (shaft) and stationary areas of the pump. The surfaces of the seal faces are super-lapped to a high degree of flatness; typically 2-3 Helium light-bands (0.00003” / 0.0008mm). If the seal faces rotated against each other without some form of lubrication they would wear and quickly fail due to face friction and heat generation. For this reason some form of lubrication is required between the rotary and stationary seal face; this is known as the fluid film.
Sealing performance over conventional O-rings is achieved by reducing particle generation, extending seal life and minimizing replacement time during preventive maintenance. Compared to traditional O-rings, this seal effectively reduces the number of dust particles generated during operation and extends the life of the machine with bonded seals installed. The seal has a working diameter range of 6.5 to 60.58mm.
DMS Seals piston seals can be used very effectively in the clearance between the two chambers of the hydraulic cylinder and cylinder. The piston seal is pushed by the pressure of the fluid. Its good working performance can improve the efficiency of the machine. Due to its excellent resistance to leakage, it helps the machine to extend the machine’s working life. Our seals provide the best tight adhesion for the sealing system with low internal leakage and frictional resistance.
Leakage of gaskets: There are four types of leakage phenomenon in general gaskets: interface leakage, penetration leakage, diffusion leakage, and damage leakage. Interface leaks: The interface will leak at the sealing interface due to insufficient gasket compression, improper flange joint surface finish, and flange deformation. For interface leakage, it can be prevented by using soft gasket to clamp in the flange face. Penetration leakage: Since most of the soft materials are made of fibers, they are easily soaked by the medium, especially the pressure. Due to capillary phenomenon, the medium will permeate to the low pressure side, forming permeation.
Support and positioning The piston and piston rod are radially supported and positioned in the cylinder barrel. Isolate the two pairs of motion pairs of piston and cylinder, piston rod and guide sleeve to prevent direct scratches, abrasions and strains between the motion pairs. Especially when the motion pairs are all steel parts, they must be isolated, otherwise they will be easily strained. The guide belt also has an important role to reduce the friction and friction work between the moving parts, reduce the ineffective work and heat. Vibration absorption and noise reduction Reduce system vibration and noise. It is mainly filled with tetrafluoroethylene and phenolic cloth, and there are also a very small amount of polyoxymethylene, nylon and soft metal. Discover even more details at https://www.dmsseals.com/.
We can design the suitable spring energized seals for your application. Our oil seals have TC, TB, SC, DC, TCV and so on. Looking forward to supply the best seals for you.(O Ring Manufacturers & Hydraulic Oil Seal Manufacturers). DMS SEALS, the seals manufacturer, was founded in 2008. DMS started by manufacturing filled PTFE seals, including bronze filled PTFE, carbon filled PTFE, graphite PTFE, MoS2 filled PTFE, and glass filled PTFE. We now also produce O-rings made of NBR, FKM, silicone, EPDM, FFKM.
Good sealing performance: Because the system works outdoors, there is no leakage oil recovery system, and the working medium will directly pollute the environment after leakage, so external leakage requirements are strict. At the same time, for the requirements of hydraulic oil heating control, pressure maintaining or maintaining position, the internal leakage requirements are also very strict. High pressure: The working pressure of the hydraulic system is high, usually above 20MPa, and the highest is about 40Mpa, which is higher than the general industrial hydraulic system pressure, so the sealing pressure resistance requirements are high.
The spring seal produced by DMS SEALS is perfect for being applied to extremely high-speed, very low-speed equipment with micro piston strokes and other special operating conditions. It can be used with rotary seals and maintains good sealing performance in violent shake and vibration motion environments. At the same time, our seals are extremely adaptable to a wide range of working media. It is resistant to a wide range of chemicals except for soluble alkali metals, high-temperature fluorine and chlorine trifluoride. Therefore, it works well with liquids such as oils and water with high and low temperature.