Taber abrasion tester supplier from China? Tensile And Compressive Test Main Parts: A pair of high precision ball screw ; Precision ball screw, high precision, high test repeatability. American brand load cell : The sensor of the utm tensile test test machine can convert the physical quantity of the measured tensile force into an electrical signal. Divided into spring sensor type, “S” type electronic sensor, spoke type sensor, hydraulic sensor. A set of servo motor and servo system respectively. The power system: servo motor and servo drivers and worm gear and rod reducer and ball screw. See additional details at taber abrasion tester.
Reagent Preparation: Prepare corresponding reagents according to different test standards and keep them as standby. If sodium perborate is required in the test, the preheating temperature shall not exceed 60℃ when preparing the solution, and it shall be used within 30 minutes at most to prevent the loss of oxidant. Solution Warm-up: Put the specified volume of solution and a specified number of steel balls into the stainless steel cup, put the stainless steel cup into the launderometer for a few minutes, preheat to the specified temperature. Then put in the prepared sample for test.
Correct use of computerized universal testing machine: When the electronic stepless speed regulation adjusts the lifting speed, it cannot be operated too fast. Before using the 50KN power machine, pay attention to check the tightening of the clamp tightening screws. When lifting the lower clamp, the movement should be stable, avoid collision, and often check the tightness of the clamp screw. When replacing the test fixture, pay attention to cooperate to prevent bruises.
Fabric color fastness to light machine Feature: The 2500W long arc xenon lamp is used to simulate the solar spectrum. High transmittance of filter combinations and use 95% of the transmittance filters and filter cartridges. With Low power consumption but achieve the same irradiation light requirements. To make the machine is more energy saving and environment friendly. Standard equipped with 420nm wave band, irradiance digital setting, real time monitoring, closed loop automatic regulation, providing the most stable irradiance test light source for different standards (340nm, 420nm, 300-400nm and 300-800nm band optional ). Test and radio transmission are powered by using light conversion technology, no additional power supply is required. With industrial temperature control (refrigeration) system for smoothly and fast adjusting temperature in test chamber.
Application of Universal Testing Machine: This types of tensile testing machines is designed for conducting tensile, compression, bending, shearing, bonding strength, peeling, tearing and other tests for shoes, rubber, plastic, leather, metal, nylon line, fabric, paper, aviation, packaging, construction, petrifaction, electrician, vehicle and other materials. It is a basic equipment of quality control, receiving inspection, physical test, mechanics research, material development.
GESTER is professionally engaged in manufacture and R&D of Textile Testing Equipment with 20+ years experience, including Fabrics tests, Yarn& Fibre tests, Color fastness tests, Flammability tests etc. Various in styles, GESTER instruments’s textile testing equipment can meet the needs of different customers.GESTER insists on the use of high-quality materials and advanced technology to manufacture textile testing instruments. Besides, we strictly monitor and control the quality and cost in each production process. All this guarantees the product to have high quality and favorable price.GESTER serves every customer with the standards of high efficiency, good quality, and rapid response. Discover even more details at https://www.gesterinstruments.com/.
ASTM D4060 Taber Abrasion Tester Uses and Factors to Be Considered: Taber Abrasion is used for measuring the wear resistance of organic coatings applied flat, rigid test samples. ASTM D1044 is used for transparent plastic materials to evaluate their capacity to maintain their optical properties, upon typical, wear to be expected while in service. Abrasion resistance to Taber Abrasion is usually measured as a weight or a coating thickness loss after a given number of cycles. Each arm, by default, is loaded to apply a 250 g. pressure on each wheel. Depending on the product/specification used, this weight can be increased to 500g or 1000g. The abrading wheels are available in different grit for a more or less abrasive action.