All posts by : John Concrane

Automotive hail repair in Macungie, PA? First let’s start with some car paint care tips: If you can not expose your car to the sunlight, you can use a hair dryer instead. Just aim the hair dryer to the areas you want to fix, and wait until the dents even out. The ideal distance between the hair dryer and the car should be 2-4 inches. While using a hair dryer, there should be an interval of 2 minutes. If the car’s paint starts discoloring, you should stop applying heat right away. Use a rubbing compound or wax to revise the paint color.

Hailstorm damage is a car owner’s worst nightmare and can easily be avoided with a few cautionary steps: try to park your car in a shaded or covered area, especially during seasons when hailstorms are prevalent. If you’re going to be going out of town for an extended amount of time, make sure that your car is parked in an enclosed area and, if possible, have someone check on it once in a while. Open spaces will leave your car helpless against the wrath of this natural phenomenon.

Another popular method for removing car dents out of plastic material involves using two popular household products: a hair dryer and compressed air. Start off by heating the car dent with the hair dryer at its highest temperature, which will expand the plastic of the car. As soon as it’s hot enough, grab the can of compressed air, turn it upside down, and begin spraying that same area. Since the cold air will cause the plastic to contract, the dent will pop out.

Don’t underestimate the necessary step of decontamination prior to application of your chosen wax. If you fail to do this step, you will get disappointing results regardless of the type of wax you have chosen. And yes…even that brand new car straight off the dealer lot will in have some form of pollutants already on the car paint from its travel from the factory to the car dealership. Clear coat is the top layer of your cars paint. It acts as a protective layer to filter out UV rays. But your clear coat is what you are trying to take care of with the above requirements. People get confused about clear coat vs. car paint. Virtually every car today is finished with a clear coat as the top layer. Think of it as car paint with no color added to it.

First, you have to pick a proper tool kit. And that’s not easy for a user who has little clue what’s going on. Some of them are cheap — low prices should raise red flags. Others are so expensive (three-figures or more) that they’re probably right up there with the cost of a decent professional repair (although, to be fair, if you buy the kit you can perform multiple repairs). Many of the high-end, expensive tools are intended to be used along the inside of the panel, much like a pro would do. (Gaining access to the inside of body panels can be a chore, though, and often involves careful removal of multiple interior trim pieces.) Alternatives (which tend to be the less expensive kits) flaunt the conventional wisdom that small dents should be massaged back out from behind the painted surface. These options instruct the user to glue a tool to the dented surface and then twist or pull on the tool to pop it out. True, you can go buy the same tools as a pro, but it takes a lot of skill and experience to use them properly. Discover additional details at Automotive Repair & Customization in Colorado Springs.

Paint Conditioner. If you’ve recently painted your vehicle or purchased a new vehicle, consider using a non abrasive paint conditioner to protect the paint. Non abrasive conditioners have to be sprayed on, in small amounts. Follow the instructions listed on the package to get good results. If you want to re-paint an old vehicle to maintain the exteriors, make sure you research the best new car paints available in the market. You need to also carefully follow car paint preparation techniques to do a good job.

PDR is a specialized form of autobody repair where technicians use special tools and techniques to slowly reduce a dent down in size until it completely disappears. PDR is a learned skill. Through trial and error, technicians gradually begin to understand the specific areas of a dent to manipulate, exactly how to manipulate certain locations of a dent, and the specialized processes and technologies used to remove a dent without the need to repaint the area.

Hot tubs complete guide? Here are several tips on how to maintain your hot tub and also a recommandation if you live in Colorado. Always shower first with soap and water to reduce the likelihood of contaminating the spa water and minimizing health risks. Lotions, oils, and other things contribute to build-up in your spa. In cold climates, it’s not advisable to drain it — so save yourself the extra cost of a possible repair bill by rinsing off before and after. Besides: isn’t it nice to get into a really clean tub? Limit your soak time to no more than 15 to 20 minutes at a time. Cool off, then re-enter if you like.

To keep detergent and soap residue out of your spa water, shower without soap before soaking in your spa, and instead of washing your bathing suit use the rinse cycle.

You can save a pretty sweet chunk of change by running your hot tub’s heater during off-peak hours, or the hours of lowest demand. Not sure when that might be? Check with your utility provider for details. And if you haven’t already, insulate your hot tub . Efficient insulation, combined with heating during off-peak hours, can cut your energy costs. It’ll also reduce the stress on your hot tub’s system and help your hardware last longer. If you’re dealing with hard water as part of your regular hot tub care routine, you already know calcium can accumulate in your jets and cause them to stiffen, clog, or stop working altogether. To help combat the build-up, grab some white vinegar and clean your spa’s valves and jets. The acidic power of the vinegar will dissolve the calcium and get things flowing again. Be sure to rebalance your water chemistry after cleaning, since acids affect hot tub pH and alkalinity levels.

Advices for buying a hot tub : Acrylic is beautiful, durable, and versatile. Molds form it into contoured shapes for comfortable, form-fitting seating in a range of sizes. Supported by a frame, a wood or synthetic cabinet surrounds the spa. The equipment is completely contained within the surround. Acrylic hot tub prices vary from a few grand to over $15,000, but high prices don’t mean high value. Skip the dealer, buy online and get more tub for less money, without skimping on quality.

But first let’s view the hot tub choice of the month : This Hudson Bay Spa from Home & Garden Spas offers an affordable high-end spa solution for the masses. The beautifully constructed hot tub comes equipped with 14 powerful jets and an energy efficient motor to provide you with a high quality therapeutic massage without consuming immense amounts of energy. Even though this tub is advertised as being big enough for 4 people it is more aptly suited for couples or small families at best. What it lacks in size it more than makes up in quality, performance and price making this hot tub a top contender on this list. See extra details on Regular Water heater maintenance Colorado.

Replace your spa filter every 1-2 years, again depending on usage. Another way to do it is to change it every 10-15 cleanings, because that’s what really breaks down a cartridge. Every time it’s cleaned, fibers loosen up and it loses a little bit of its dirt trapping ability. Keep track of your spa filter’s age and/or cleaning cycles, because at some point soon it’s gonna be “Hasta la vista, baby!”

This spa care tip is so often forgotten. However, if the skimmer starts to suck air, it could possibly damage the pump. The water level should be in the middle of the skimmer intake or a little higher. You don’t want it too high, and you never want to overflow the spa, so keep a close eye on the water level while filling.

Your daily maintenance tasks are all about ensuring good water quality. In a hot tub that means checking two things: PH and sanitizer levels. This is easy stuff, and can generally be accomplished by dipping a single, color-coded test strip into the water to check that everything is as it should be. If you’re diligent about maintaining your tub, most days this won’t mean doing anything more than walking out to your tub, dipping the test stick in the water, and heading back inside. If your PH or sanitizer levels need adjusting, however, you’ll need take an extra few minutes to dump the proper additive into your water to get things back their proper levels. Doing so will prevent a host of problems, including scaling, mineral buildup, corrosion, skin irritation, and cloudy and stinky water.