Posts in category: Industrial

Excellent pneumatic press machine provider in China? Fast delivery standard machines stock for sale: Standard C frame single crank press and eccentric press are always some units stocking for sale. 2 weeks to 30 days lead time for customized order. Big press line such as car body parts stamping line could be ready for shipment within 4 months after order. Read more info on power press machine. We can provide installation service for all the sold out machines at customer factory. Small machines can be shipped assembled and some big machines must be shipped disassembled. That is why we provide installation service to our customer.

Even if there are shelves full of molds, don’t assume that these molds are suitable for the newly purchased machine. The wear of each mold must be checked by measuring the length from the front end of the punch to the shoulder and the length between the shoulder of the female mold. For conventional ols, the deviation per foot should be about t0.001 inches, and the total length deviation should not be greater than t0.005 inches. As for the precision grinding mld, the accuracy per foot should be ±0.0004 inches, and the total accuracy should not be greater than ±0.002 inches. It is best to use fine grinding molds for CNC bending machines, and conventional molds for manual bending machines.

Hydraulic transmission is adopted, and the slider part is composed o slide, an oil cylinder and a fine-tuning structure of a mechaicl stoper. Te left and right oil cylinders are fixed on the frame, the piston (rod) drives the slider to move up and down through hydraulic pressure, and the mechanical stop is controlled by the numerical control system to adjust the value; Workbench part: controlled by the button box, the motor drives the stopper to move back and forth, and the moving distance is controlled by the numerical control system. The minimun reading is 0.01 mm (the front and rear positions have travel switch limits).

Under the same load, the deflection of the worktable and sliding block of the 10-foot machine is 4 times that of the 5-foot machine. This means that shorter machines require fewer shim adjustments to produce qualified parts. Reduced shim adjustment and shortened preparation time. Material grade is als a key factor. Compared with low-arbon sel, the load required by stailes stee is usuall increasedby about 50%, while most grades of soft aluminum are reduced by about 50%. You can get the machine’s tonnage table from the bending machine manufacturer at any time. The table shows the estimated tonnage required per foot length unde diffrent thicknesses and different materials.

Modern and sophisticated materials are used in automotive engineering not only for the outer skin and structure of the actual car bodies but are also used in vehicle components such as the chassis, drive train, seats or trim parts. Auminum and steel are used for many components in the form of strips, sheets or plates, which are processed and formed in various manufacuring processes from semi-finished products to finished components. Even during these process steps, special demands are placed on the components. Due to the automated handing, good flatness and theloest possible degree of cut are very important for a machining procss itout comliations. Ifhese qualit criteria o not correspond to the defined specifications, there is no process reliability. Find even more details at https://www.pressmachine-world.com/.

Golden horse rides provider with Jinma Rides? Engaging top professionals in the industry, Jinma has been able to assemble a professional research and development team, headed by leading experts in respective disciplines. This strong team is composed of 9 senior engineers, including 2 professor-level engineers, and 180 full-time designers and developers, in disciplines of mechanical engineering, mechanics, automation, electronic information, computer science, composite materials, industrial design, art and craft, and multi-media content creation. Discover additional info at amusement rides manufacturers.

A Carousel or Merry go Round ride is a time-tested popular amusement ride. It features a rotating patform on which exquisitely crafted FRP horses and chariots are mounted. Those horse are designed to move up and down. With the platform rotating, it creats a feeling of galloping for the riders. The earliest recorded carousel appeared in the Byzantine Empire. Around 1860, the first carousel powered by steam appeared in Europe. Nowadays, you may find various carousels at parks, playgrounds, shopping malls and other venues.

As amusement rides are one kind of special equipment, each production link is directly or indirectly related to its safety performance. Through skill competition, the craftsman spirit can be carried forward and the industry skills improved by building a platform for contestants to show their skill quality and level. It is deemed as a boost to workers’ professional quality and advanced manufacturing industry, and to further standardization and perfection of their skill level. The competition involved 224 participants and covered 87.5% of types of work in the workshops. Each employee actively took part in the competition and showed their true skill level by completing the competition tasks within the specified time according to the drawings or competition rules. After fierce competition, 56 workers finally stood out, which displays Jinma’s pursue for high-standard and high-quality products.

Jinma Rides keeps ramping up R & D in immersive attractions that integrate the ride system with various effects including lights, sounds, wind and animation to replay a story in the most vivid way. Motion Dark Ride adopts innovative six degree of freedom dynamic platform to take passengers through the dynamic cabin to shuttle through different story scenes composed of theme landscape, high-definition film, machine model, sound effect, etc. It is definitely an excellent experiential ride attractions with high immersion.

Jinma operates its businesses in the emerging cultural industry, cultural tourism equipment manufacturing industry, and game&amusement industry. By integrating creative concepts, advanced technologies and safety concepts, Jinma has developed a large portfolio of more than 300 rides under 13 categories, covering coasters, tower rides and immersive attractions, and many of them are the first of its kind ever built in China and abroad. Read additional information on https://www.jinmarides.com/.

Premium level indicator manufacturer? The radar level gauge works by electromagnetic waves. Its working principle is to measure the specific liquid level by transmitting electromagnetic waves to the measured target. After the electromagnetic waves are emitted, they are reflected by the medium. For the radar level gauge, its key function is to ensure that it can transmit magnetrol guided wave radar signals smoothly. In our industrial production site, interference often occurs, so which interference sources will affect the measurement of the radar level gauge? let’s see. Read additional information at level switch manufacturer. OEM Service-can be customized according to the application of customer,such as level gauge,level switch and level indicator.

Working principle: Working principle of radar level gauge: UHF electromagnetic waves are transmitted to the liquid level of the container under test through the cable or antenna. When the electromagnetic wave touches the liquid level and is reflected back, the instrument detects the time difference between the initial wave and the echo, thereby calculating the liquid level height. Select guided wave radar or airborne radar according to the dielectric constant and measurement length of the measured medium.

Measurement accuracy, the accuracy of ordinary radar is generally ±10mm, and the accuracy of precision radar is ±3mm. Selection according to the actual needs of production. Range, according to actual needs, choose the antenna size. Note that the actual range is reduced in complex environments. Antenna type and antenna size, the larger the antenna size, the larger the measured range and the stronger the anti-interference ability. The antenna types of radar level gauge are rod type, bell mouth type, paraboloid and so on.

The influence of dust accumulation on the transmitter head of the radar level meter, due to the large amount of dust in the working condition of the radar level meter, the dust is easy to adhere, and affected by the ambient temperature, the dust is wet and easy to agglomerate, and the dielectric constant will become larger and adhered The transmitter head and the wall of the bell mouth of the radar level meter affect the accuracy and stability of the radar measurement.

As one of the most professional magnetic level indicators manufacturers in China,Guangdong Kaidi Energy Technology Co., Ltd. provides customized solutions for a range of industrial automation process applications,such as mechanical float level indicator.We specialized in radar level gauge, fork type level switch,etc. These were implemented successfully, and KAIDI magnetic level gauge manufacturers products,such as radar level meter, magnetic level indicators, can be used in many different industries such as food & beverage, water, energy, pharmaceutical etc. Find extra info on kaidi86.com.

High quality nanocrystalline transformer core manufacturer today? Transmart transformer manufacturers are an export oriented company with customers located in 40+ countries. We supply high quality tape wound cores in Nanocrystalline, Amorphous and Silicon Steels. Product applications including Common mode chokes ,Hall Effect Current Sensors, Low Voltage and Medium Voltage instrument transformers, Earth Leakage Circuit Breakers ,Reactors, Inductors etc. See more information at https://www.transmart.net/nanocrystalline-cores. Transmart Industrial insists on the use of high-quality materials and advanced technology to manufacture soft magnetic materials. Besides, we strictly monitor and control the quality and cost in each production process. All this guarantees the product to have high quality and favorable price.Transmart supplier has a complete and mature service team to provide excellent services for customers and seek mutual benefit with them.

We know that the actual transformer always works in AC state, and the power loss is not only on the resistance of the coil, but also in the iron core magnetized by alternating current. Usually, the power loss in the iron core is called “iron loss”. The iron loss is caused by two reasons, one is “hysteresis loss” and the other is “eddy current loss”. Hysteresis loss is the iron loss caused by the hysteresis phenomenon in the magnetization process of the iron core. The size of this loss is directly proportional to the area surrounded by the hysteresis loop of the material. The hysteresis loop of silicon steel is narrow, and the hysteresis loss of transformer core made of silicon steel is small, which can greatly reduce its heating degree.

Commonly used transformer cores are generally made of silicon steel sheets. Silicon steel is a kind of steel with silicon (silicon is also called silicon), and its silicon content is 0.8 ~ 4.8%. The reason why silicon steel is used as the iron core of transformer is that silicon steel itself is a magnetic material with strong magnetic conductivity. In the energized coil, it can produce large magnetic induction intensity, which can reduce the volume of transformer. rolled silicon steel sheet is selected. It is cut into long pieces according to the size of the required iron core, and then overlapped into “day” shape or “mouth” shape. In principle, in order to reduce eddy current, the thinner the silicon steel sheet, the narrower the spliced strip, and the better the effect. This not only reduces the eddy current loss and temperature rise, but also saves the material of silicon steel sheet. But in fact, when making silicon steel sheet iron core. Not only from the above favorable factors, because making the iron core in that way will greatly increase the working hours and reduce the effective section of the iron core. Therefore, when making transformer iron core with silicon steel sheet, we should start from the specific situation, weigh the advantages and disadvantages and choose the best size.

As one of Transmart Industrial’s multiple product series, mumetal cores series enjoy a relatively high recognition in the market. Transmart Industrial provides diversified choices for customers. The mu-metal cores are available in a wide range of types and styles, in good quality and in reasonable price.Transmart Industrial effectively improves after-sales service by carrying out strict management. This ensures that every customer can enjoy the right to be served. Find extra details on transmart.net.

Amorphous nanocrystalline alloys are competing with soft ferrite in the field of medium and high frequency. In 10kHz to 50KHz electronic transformer, the working magnetic flux density of iron-based nanocrystalline alloy can reach 0.5T and the loss P0.05 5 / 20K ≤ 25W / kg, so it has obvious advantages in high-power electronic transformer. In 50 kHz to 100 kHz electronic transformer, the loss of iron-based nanocrystalline alloy is P0.05 2 / 100k is 30 ~ 75W / kg, Fe based amorphous alloy P0.05 2 / 100k is 30W / kg, which can replace some ferrite markets.

On the one hand, it can isolate eddy current, and the data is suitable for higher frequencies; On the other hand, due to the gap effect between particles, the data has low permeability and constant permeability; Because the particle size is small, there is basically no skin phenomenon, and the change of permeability with frequency is relatively stable; Moreover, the powder core can be prepared into special-shaped parts of various shapes for different fields; Finally, the damaged strip in industry can be crushed into magnetic powder, and then made into magnetic powder core, which can reduce the loss and improve the use value of data. The magnetoelectric properties of magnetic particle core mainly depend on the permeability of powder material, size and shape of powder, filling coefficient, content of insulating medium, forming pressure and heat treatment process.

Top rated ethylene bis-stearamide provider? Sainuo is the leading polyethylene wax manufacturer and EBS wax supplier for PE wax, Ethylene bis-stearamide, etc. Polyethylene wax lubrication dispersant with an annual output of 30,000 tons, production scale of international production base, 60,000 tons of production and sales capacity. For quotation, TDS, samples request, please contact us. If there is anything you’re not sure about or you just need a hand getting set-up you can call or email us(polyethylene wax supplier). Discover extra information on n n ethylene bis stearamide.

Its performance is comparable to the US Honeywell AC wax. It can improve the production efficiency of plastic processing, reduce the production cost, has good compatibility with polyolefin resin, etc. Oxidized PE wax has good moisture resistance at normal temperature, strong chemical resistance, excellent electrical properties, and can improve the appearance of finished products. Oxidised polyethylene wax can replace the products of Mengdan wax, Sichuan wax, liquid paraffin, microcrystalline paraffin, natural paraffin and polyethylene wax, etc, and its performance is comparable to that of the Honeywell A-C wax.

Intermediate content of 10-12%, mainly used for powder coating treatment and increase capacity flow. In the grinding pigment (filling) process of producing pigments and inks, a metering coupling agent can be directly input, which can improve the dispersibility of the pigment or filler, shorten the grinding time, increase fineness, brightness, and reduce viscosity. Atactic polypropylene is effectively solve the problem of high filling system debris, improve the toughness of products, can replace the use of carrier, but also can replace the use of lubrication. Atactic polypropylene is used in filler masterbatch, etc Discover extra information at sainuowax.com.

Colorants are the main components of color masterbatch. They provide all the required colors and characteristics. Inorganic pigments: black and white pigments represented by titanium dioxide and carbon black; Iron oxide, metal oxide mixed crystal series, ultramarine, metal sulfide, etc; Organic pigments: azo series, phthalocyanine series, heterocyclic (fused ring) series, etc; Organic dyes: solvent dyes, disperse dyes (part), vat dyes (part); Effect pigments: Mica (pearlescent) pigment, copper gold powder, aluminum silver powder (slurry).

The internal and external lubrication is insufficient, the melt viscosity is large, the plasticizing torque is large, and the melt wall sticking phenomenon is serious. There is a yellow decomposition line on the material surface, the surface smoothness is poor, and the mechanical properties of the product are reduced: the internal and external lubrication is excessive, the plasticizing torque is small, and the melt plasticization is obviously insufficient. Although the product has good smoothness, the pressure point adhesion is poor, which seriously affects the mechanical properties of the product.

High quality synthetic blood penetration tester factory? Universal testing machine (also known as tensile testing machine) that performs tensile, compression, flexure, peel, tear, shear, friction, and other types of mechanical testing in accordance with ASTM, ISO, and other industry standards. GESTER Abrasion Tester Professional manufacturer, providing a full range of solutions, Martindale Abrasion Tester in line with ASTM, ISO and other standard requirements, factory direct sales. Find more details on https://www.gesterinstruments.com/mask-tester.

Application of Universal Testing Machine: This types of tensile testing machines is designed for conducting tensile, compression, bending, shearing, bonding strength, peeling, tearing and other tests for shoes, rubber, plastic, leather, metal, nylon line, fabric, paper, aviation, packaging, construction, petrifaction, electrician, vehicle and other materials. It is a basic equipment of quality control, receiving inspection, physical test, mechanics research, material development.

Correct use of computerized universal testing machine: Make sure all wiring is correct before the tensile testing machine is operated and preheat for at least 15 minutes to package the stability of the sensor. According to the test, the position of the upper and lower limit blocks is reasonably set to prevent the instrument from running over the stroke and causing damage to the fixture and the sample. When pressing the fast up button or the fast down button, do not put your hand between the moving beam and the fixed specimen, fixture or test device to avoid injury.

Testing to ASTM D4060 involves mounting a flat specimen to a turntable that rotates horizontally at a fixed speed. Two arms, each supporting an abrading wheel, are then lowered so that each wheel touches the surface. Before starting the test, a “suction arm” is lowered between the wheels to remove the abraded material from the sample’s surface. The turntable then starts rotating forcing rub-wear action of the wheels against the sample’s surface for the specified number of cycles or until a given mass of coating has been lost or until the wheels start exposing the substrate.

The principle of testing that you should know: Stitch the sample with one or two pieces of specified multi-fiber adjacent fabric, which is placed in soap solution or other washing solution, mechanically stirred at the specified time and temperature, cleaned and dried. Taking the original sample as the reference sample, assess the discoloration of the sample by the left gray scale, and then assess the color stain of the adjacent fabric by the right gray scale. Find even more details at https://www.gesterinstruments.com/.

High quality nanocrystalline toroidal core supplier in China? Transmart transformer manufacturers are an export oriented company with customers located in 40+ countries. We supply high quality tape wound cores in Nanocrystalline, Amorphous and Silicon Steels. Product applications including Common mode chokes ,Hall Effect Current Sensors, Low Voltage and Medium Voltage instrument transformers, Earth Leakage Circuit Breakers ,Reactors, Inductors etc. Read even more information on nanocrystalline toroidal core. Soft magnetic materials are those materials that are easily magnetised and demagnetised. They typically have intrinsic coercivity less than 1000 Am-1. They are used primarily to enhance and/or channel the flux produced by an electric current. The main parameter, often used as a figure of merit for soft magnetic materials, is the relative permeability (µr, where µr = B/ µoH), which is a measure of how readily the material responds to the applied magnetic field. The other main parameters of interest are the coercivity, the saturation magnetisation and the electrical conductivity.

As for why it can boost and depressurize It needs to be explained by Lenz’s law The magnetic flux generated by the induced current always hinders the change of the original magnetic flux. When the original magnetic flux increases, the magnetic flux generated by the induced current is opposite to the original magnetic flux. In other words, the induced flux generated by the secondary winding is opposite to the main flux generated by the original winding, so the secondary winding has a low-level alternating voltage. So The iron core is the magnetic circuit part of the transformer The winding is the circuit part of the transformer.

The common mode inductor using nanocrystalline core material can well suppress the peak voltage, protect sensitive components, and reduce the motor shaft voltage. Because of the unique characteristics of nanocrystalline core, it has been well used in some high-power system industries. Electric energy meter, power meter, ammeter, electric measuring equipment and other instrument fields. Various power current transformers in power transmission and distribution monitoring system. Leakage protection, relay protection, servo motor protection, fire monitoring, etc Current and voltage data sampling, etc.

Amorphous Core is preferred choice for transformers required low losses at high frequency. We have amorphous c-cores,amorphous ribbon cores,amorphous cut cores,amorphous core transformers . Please find out more about crgo core material. There are 50% and 80% nickel iron materials available, in which we manufactures Mumetal Toroidal core and Mumetal C-core, for the applications in high quality Current Transformers and power supplies industries. Discover even more info at https://www.transmart.net/.

Amorphous nanocrystalline alloys are competing with soft ferrite in the field of medium and high frequency. In 10kHz to 50KHz electronic transformer, the working magnetic flux density of iron-based nanocrystalline alloy can reach 0.5T and the loss P0.05 5 / 20K ≤ 25W / kg, so it has obvious advantages in high-power electronic transformer. In 50 kHz to 100 kHz electronic transformer, the loss of iron-based nanocrystalline alloy is P0.05 2 / 100k is 30 ~ 75W / kg, Fe based amorphous alloy P0.05 2 / 100k is 30W / kg, which can replace some ferrite markets.

Characteristics and application of nanocrystalline magnetic core: High permeability, nanocrystalline Fe73 5Cu1Nb3Si13. 5B9 alloy has high saturation magnetic induction. The material becomes brittle after heat treatment and is easy to be processed into alloy powder. Compared with the nanocrystalline magnetic core wound with strip, the magnetic permeability of the nanocrystalline magnetic core is still very low and the soft magnetic properties are unstable. At present, the urgent problems to be solved are as follows: 1. Effectively control the growth of nanocrystals during heat treatment; 2. Molding of magnetic particle core; 3 Effect of heat treatment specification on soft magnetic properties of magnetic particle core.

High quality cartridge seal manufacturer and supplier today? Take the mechanical seals – the most commonly used and popular products now – as the example: It is also known as a face seal, which is a rotary machine shaft seal device that can avoid the leakage of the fluid. It is widely used for the rotation of the shaft seal, for pumps, kettle, compressor, and other similar equipment. There are a lot of materials for manufacturing the mechanical seals, including rubber, stainless steel, PTFE, carbon, ceramic, Sic and TC. See even more details on cartridge seal. Lepu Seal mechanical seal China supplier provides best cartridge seal. Cartridge seals are self conantainered units consisting of a shaft sleeve, seal, and gland plate.

Lepu Seal always puts quality the first. During the production process, we are detail-oriented to each step. Advanced production technology is utilized and carried out for the manufacturing of the product, which makes it perfectly prevent the fluid and solid particles from leaking into the machine. In addition, exquisite workmanship guarantees the high quality. It is characterized by its durability, reliability, and ageing resistance.

For better satisfying the needs of customers, the product can be provided with different shaft sizes ranging from 24mm to 100mm. In Lepu Seal, Alfa Laval mechanical seal LPSRU3 is a professionally designed mechanical seal replacement for Alfa Laval pump SRU3. Super light screws are designed on the seal ring, which both guarantees the easy operation and strong structure. Each product is designed with precise dimension ranging from 20mm to 45mm, which can satisfy the different needs of customers.

LEPU SEAL(China mechanical seal manufacturers) provides a wide range of Mechanical Seal for customers. Mechanical Seal is in line with stringent quality standards. The price is more favorable than other products in the industry and the cost performance is relatively high. LEPU SEAL insists on the principle to be honest, practical, and efficient. We continue to accumulate experience and improve service quality, so as to win praise from customers. We supply high-quality Mechanical seal, Grundfos mechanical seal, Burgmann mechanical seal, Cartridge Seal, Bellows Seal,etc. See additional details at https://www.lepuseal.com/.

We’ve absorbed plenty of experienced technicians, which guarantees that there is no sticking or clogging, making the design rugged and reliable. The seal is independent of direction of rotation, which provides more convenience for the movement of the product. It also has precise operating parameters including less than 0.5MPa operating pressure and wide temperature ranging from -20? to 120?. Compared with other series of seals, it has reliable sealing performance, small leakage, long service life, and low maintenance frequency. Thanks to its stable chemical performance, the product can stay perfect for more than one and a half years or even longer in the oil and water, or all kinds of corrosive acid, alkali, salt. Besides that, the shaft or bushing won’t get worn easily. One thing that needs to be mentioned is that this kind of products has good vibration resistance and will not be easily affected by the vibration and yaw of the rotating shaft.